铁艺大门在日常生活中被广泛使用。我们走在路上基本上到处都能看到铁艺大门的使用。关于济南铁艺大门相关工艺处理要点，下面我们来了解一下。

Iron gates are widely used in daily life. We can basically see the use of iron gates everywhere on the road. Now let's take a look at the processing points related to Jinan Iron Gate.

1.手工处理主要使用砂布、刮刀、锤凿、钢丝刷、废砂轮等工具。并通过人工打磨、敲击、刷洗等方式去除铁艺护栏表面的锈皮、水垢、焊渣、灰尘等污垢。

1. Manual treatment mainly uses abrasive cloth, scraper, hammer chisel, wire brush, waste grinding wheel and other tools. The rust scale, scale, welding slag, dust and other dirt on the surface of iron guardrail shall be removed by manual grinding, knocking, brushing and other methods.

2.机械处理常用的工具有气刷、除锈枪、抛光砂轮、气铲等。借助机械力的高频冲击和摩擦，除锈并去除水垢旧漆等污垢。

2. Common tools for mechanical treatment include air brush, derusting gun, polishing wheel, air shovel, etc. With the help of high-frequency impact and friction of mechanical force, derusting and removing scale, old paint and other dirt.

3.喷雾处理是利用机械离心、压缩空气、高压水流等。作为向铁艺护栏表面抛撒磨料、砂石、钢丸的动力，以冲击和磨掉氧化皮、锈迹、旧漆、型砂等。4.化学处理是用特殊配方的酸液浸泡溶解铁艺制品，通过化学反应去除氧化皮、锈迹、油污，称为“酸洗”。

3. Spray treatment uses mechanical centrifugation, compressed air, high-pressure water flow, etc. It is used as the power to scatter abrasives, sand and steel shot on the surface of iron guardrail to impact and grind off oxide skin, rust, old paint, molding sand, etc. 4. Chemical treatment is to soak and dissolve iron products with acid solution of special formula, and remove oxide skin, rust and oil stain through chemical reaction, which is called "pickling".

使用时间久了之后，我们会在铁艺大门上涂上一层特殊的防锈防腐油。铁艺大门涂一层静电喷涂防锈油，这是一种绝缘油，有以下要求：

After a long time of use, we will apply a special layer of anti rust and anti-corrosion oil on the iron gate. The iron gate shall be coated with a layer of electrostatic spraying antirust oil, which is an insulating oil and has the following requirements:

(1)外观应均匀透明，即无浑浊或沉淀。

(1) The appearance shall be uniform and transparent, that is, without turbidity or sediment.

(2)静电喷涂防锈油应易带电，常温耐油性不低于600k，击穿电压不低于20kV。过小的油阻会威胁操作人员的人身，降低设备的性和可靠性，喷油雾化效果差。

(2) The electrostatic spraying antirust oil shall be easy to be electrified, the oil resistance at room temperature shall not be less than 600k, and the breakdown voltage shall not be less than 20kV. Too small oil resistance will threaten the personal safety of operators, reduce the safety and reliability of equipment, and the atomization effect of fuel injection is poor.

(3)上油是在潮湿的环境中进行的，这样容易使水混入油中。当油中水分含量超过0.05%时，会对供油系统造成严重危害。此外，水容易使油变质，水分过多会使油乳化，影响涂油钢板(带)的防锈效果，降低油的电阻值。所以要求油中的含水量不能超过0.03%。

(3) Oiling is carried out in a humid environment, so that water can easily mix with the oil. When the water content in the oil exceeds 0.05%, it will cause serious harm to the oil supply system. In addition, water is easy to deteriorate the oil, and excessive water will emulsify the oil, affect the rust prevention effect of the oiled steel plate (strip), and reduce the oil resistance. Therefore, the water content in the oil shall not exceed 0.03%.

(4)油中残留的悬浮或沉淀的固体杂质会造成供油管路中部件的磨损和堵塞，也影响涂油质量。如果吸油过滤器被杂质堵塞，会造成供油泵吸力不足，产生气蚀，供油管路振动，产生噪音。

(4) The suspended or precipitated solid impurities left in the oil will cause the wear and blockage of the components in the oil supply pipeline, and also affect the oil quality. If the oil suction filter is blocked by impurities, it will cause insufficient suction of the oil supply pump, cavitation, vibration of the oil supply pipeline and noise.

如果细机油滤清器被杂质堵塞，滤芯可能会破裂，附着在滤芯上的杂质可能会进入被过滤的管路。因此，应保证油中杂质含量不大于0.005%，杂质粒径不大于0.01mm，使供油系统的滤油器、电磁换向阀的芯棒和喷油梁的刃口狭缝不被杂质堵塞。

If the fine oil filter is blocked by impurities, the filter element may break, and impurities attached to the filter element may enter the filtered pipeline. Therefore, it shall be ensured that the content of impurities in the oil is not more than 0.005%, and the particle size of impurities is not more than 0.01 mm, so that the oil filter of the oil supply system, the mandrel of the electromagnetic reversing valve and the cutting edge slot of the fuel injection beam are not blocked by impurities.

由于应用科学，铁艺大门厂家不易生锈腐蚀。但由于气候的变化，酸雨的形成，不可避免的会出现生锈或腐蚀的情况，所以要多加注意它的维护保养。更多事项就来我们网站//www.lefouu.com咨询！

Due to scientific application, iron gate manufacturers are not easy to rust and corrosion. However, due to climate change and the formation of acid rain, rust or corrosion will inevitably occur, so more attention should be paid to its maintenance. Come to our website for more information //www.lefouu.com consulting service